Measuring methods
Thread gauges
Use a thread plug gauge on an internal thread and a thread ring gauge on an external thread. Complete both the GO and NO-GO checks; one check alone cannot cover both sides of the allowed range.
On this page
Which gauge fits which thread?
A thread plug gauge checks an internal thread, while a thread ring gauge checks an external thread. Nominal diameter, pitch, hand and tolerance class must match the workpiece callout.
For M20×2.5, a gauge made for another pitch is the wrong gauge even if its diameter appears close. A forced or mismatched gauge cannot produce a valid result.
What does the GO gauge check?
The GO gauge checks the maximum-material-side functional limit over the specified engagement length. It should assemble through that required length without being forced.
This is a functional check, not a one-number comparison in real gauging. Pitch or lead error, flank-angle error, profile and the engagement length can all affect whether the full-form GO gauge assembles.
What does the NO-GO gauge check?
The NO-GO gauge limits the other side of the pitch-diameter range. Its permitted entry depends on the applicable gauge standard, gauge type and workpiece conditions.
Do not turn “NO-GO” into a universal rule of zero turns. Without the relevant clause of GB/T 3934-2025, no fixed number of turns is stated here.
What does a pass prove?
A completed GO/NO-GO check gives an attribute result for that gauging system; it does not report pitch diameter, pitch or flank angle as measured values. Both checks must satisfy the applicable rule before the thread passes.
GB/T 3934-2025 is the current Chinese specification for general-purpose screw-thread gauges. It took effect on 1 May 2026 and replaced GB/T 3934-2003.
In KELIBRON
KELIBRON does not yet have M20×2.5 plug or ring gauges in the public lab. In the workshop, a thread gauge check is a go/no-go trial, not a size reading.
Both checks must be made: GO enters and NO-GO stops before a pass is possible. Real GO and NO-GO ring gauges can be separate tools. This binary rule is a teaching simplification; it does not model pitch, flank angle, profile, engagement length, gauge manufacture or wear.
References
- GB/T 3934-2025《普通螺纹量规技术条件》 · 国家市场监督管理总局、国家标准化管理委员会
- NPL Notes on Screw Gauges · National Physical Laboratory
- Screw-Thread Standards for Federal Services, Handbook H28 (1969), Part I · US National Bureau of Standards
- EURAMET cg-10 v2.1 — Determination of Pitch Diameter of Parallel Thread Gauges by Mechanical Probing · EURAMET
- 金莹 主编,《公差配合与技术测量》,清华大学出版社,2014(2024 年第 4 次印刷),ISBN 978-7-302-37145-8 (cited by number; no public page) · 清华大学出版社
How the guides are checked against these sources: About KELIBRON.
Practise the shared basics on a caliper
Questions
Which thread gauge checks a nut?
A thread plug gauge checks an internal thread such as a nut; a ring gauge checks an external thread.
Can I pass a thread after only the GO check?
No. GO and NO-GO checks control different boundaries, so both checks must be completed.
Does a thread gauge measure pitch diameter?
It gives an attribute result. It does not report pitch diameter or each thread error as a numerical measurement.
Practise the basics first
Cleaning, zero checks, square positioning, light even force and reading to the scale interval are the same on every instrument; practise them in a caliper scene.
Related guides
- Measuring methodsMetric thread basicsM20×2.5 identifies a general-purpose metric thread with a 20 mm nominal diameter and 2.5 mm pitch.
- Tolerances and decisionsGo no go gauges: how a plain limit gauge judges a sizeCheck the go end and no-go end as a pair: the go end must pass and the no-go end must stop.
Measurement basicsSizes and tolerances on a drawingStart with a concrete size: Ø20 0/−0.05 has a lower limit of 19.95 mm and an upper limit of 20.00 mm.
